Пользователь:
KArIP-адрес скрыт
Дата: 11.10.2006 21:32
Re: Стыковка с Панасом
Как я понял - нужно о проблеме поподробнее
В Панасонике можно програмить следующее
В мануале написано
Функции платы (KX=T96188) цифровой соединительной линии E1
1. Интерфейс E1 (1 контур на одной плате).
E1 является цифровой линией передачи с пропускной способностью 2.048Mбод/сек.
E1 может поддерживать 30 голосовых диалогов.
Формат цикла: PCM30/PCM30-CRC
Линейное кодирование: AMI/HDB3
Тип канала: DR2/E&M-C/E&M-P
Сигнализация: Импульсная/DTMF/MFC-R2
Теперь программирование
Для каждого канала можно выставить следующие параметры
- Параметр Channel Type/Тип канала
Значение по умолчанию Undefined/Не определен
Диапазон значений
1. Undefined/Не определен
2. DR2
3. E&MP
4. E&MC
Описание/Функция Определяет тип интерфейса E1 для каждого канала.
1. Undefined/Не определен: тип канала не назначен.
2. DR2: Цифровая система связи R2
3. E&MP: Импульсная система E&M
4. E&MC: Непрерывная система E&M
- Параметр Receiver Type/Тип приемника
Значение по умолчанию Undefined/Не определен
Диапазон значений
1. Undefined/Не определен
2. Pulse/Импульс
3. DTMF/Двутональный мультичастотный сигнал
4. MFCR2
Описание/Функция Определяет тип набора номера при приеме входящего вызова.
1. Undefined (Не определен): тип приемника не определен.
2. Pulse (Импульс): отправка/прием сигнала DP
3. DTMF (Двутональный мультичастотный сигнал): отправка/прием тонального (DTMF) сигнала
4. MFCR2: отправка/прием сигнала MFCR2 (только цифровая система связи R2)
Теперь програмирование линий
Для линий можно выставить следующие характеристики
Параметр Incoming Type/Входящий тип
Значение по умолчанию для нашей платы
(2) DID(Прямой входящий набор номера): плата DID / DID2W /DIDMFC / E1 [DR2] / E1 [E&MC (MFCR2)] / E1 [E&MP (MFCR2)] / T1 [DID]
(3) TIE (Соединительная линия):плата E1 [E& MC (Pulse, DTMF)] / E1 [E&MP (Pulse,DTMF)] / E&M / T1 [TIE]
Диапазон значений
1. DIL/Прямой входящий вызов
2. DID/Прямой входящий набор номера
3. TIE/Соединительная линия
4. DDI/Прямой входящий набор номера
5. MSN/Множественный абонентский номер
Параметр Dial Type/Тип набора
Значение по умолчанию
Pulse10/Импульс10): [SA],
DTMF80: другие (плата DID2W/E1/E&M/ELCOT/GCOT/LCOT/PCOT/RCOT/T1),
ISDN (плата BRI/PRI23/PRI30),
MFCR2 (плата DID-MFC)
Диапазон значений
1. Pulse10/Импульс10 (10 PPS)
2. Pulse20/Импульс20 (20 PPS)
3. DTMF80 (80 мсек.)
4. DTMF160 (160 мсек.)
5. MFCR2
6. ISDN
А тут Card Properties (E1)
Used to assign the parameters for the E1 card.
- Line Coding
1.HDB3 (Default)
2.AMI
- Frame Sequence
1.PCM30 (Default)
2.PCM30-CRC
- Frame Option
1.C = 0, D = 1 (Default)
2.C = 1, D = 1
3.C = A, D = B
4.C = 0, D = 0
5.C = 1, D = 0
- First Dial Timer
32 - 8160 ms in 32 ms increments (Default: 64 ms)
- Pulse Feedback Tone
1.Yes (Default)
2.No
- Signaling Bit Monitor (Port No.)
1.Disable (Default)
2.Port No. 1-24
- Signaling Bit Monitor (Mode)
1.Mode 1: LED (SYNC ERROR/RAI/AIS/SYNC)=(TR-A/TRB/TR-C/TR-D bit)
2.Mode 2: LED (SYNC ERROR/RAI/AIS/SYNC)=(RX-A/RXB/RX-C/RX-D bit)
3.Mode 3: LED (SYNC ERROR/RAI/AIS/SYNC)=(TR-A/TRB/RX-A/RX-B bit) (Default)
- Inter-digit Pause
1.630 ms
2.830 ms (Default)
3.1030 ms
- Flash Detection
1.Yes
2.No (Default)
Activates or deactivates the detection of Flash signal transmitted from otherExchange System
which is connected to your system via E1 Line.If set to "No," the system does not recognise a
switchhook flash.
- Flash Detection Timer
1. 208 - 1016 ms (Default)
2. 80 - 1016 ms
3. 208 - 1544 ms
4. 80 - 1544 ms
Specifies the time range in milliseconds that the system requires to recognise a switchhook flash.
- Answer Decision Timer
32 - 8160 ms in 32 ms increments (Default: 32 ms)
Specifies the time range in milliseconds that the system requires to recognise the answer signal.
- Seizure ACK Wait Timer
0.5 - 10 s in 0.5 s increments (Default: 2.5 s)
Specifies the Seizure ACK waiting time for DR2 (Digital System R2) signals.
ACK is an ASCII or EBCDIC code character indicating a positive acknowledgement that
a message has been received correctly.
- Pulse Type
1.Type-A (Normal) (Default)
2.Type-B (New Zealand)
3.Type-C (Sweden)
Line Signal Setting
- DR2 Signaling Type
1.Normal (Default)
2.Option-1
3.Option-2
4.Option-3
Specifies the control type of the DR2 (Digital System R2) signals.
Option-1: - Seizure ACK: A=0, B=0- Without Answer- Metre Pulse Monitor A bit: 0 -> 1, B bit: 0 -> 1
Option-2: - Group-C and Group III signals are used in the ANI (Automatic Number Identification) sequence.
Option-3: - Reserved for future use.
- Inter-digit Timer (Option-1/Option-3)
3 - 15 s (Default: 5 s)
Specifies the pseudo-answer time.
[Note]- This parameter is valid when 'Option-1' or 'Option-2' is selected in "DR2 Signal Type" menu.
- Bit Position for Dial Pulse
1.A-bit (Default)
2.B-bit
Specifies the position of the Dial Pulse control bit of the DR2 Signals.
- Bit Position for Clear Back
1.A-bit (Default)
2.B-bit
3.A-bit&B-bit
Specifies the position of the Clear Back Signal control bit of the DR2 Signals.
- E&M Signaling Type
1.Type-1
2.Type-2 (Default)
3.Type-3
4.Type-4
Specifies the control bit of the E&M signals.
Type-1: A bit = 0
Type-2: A bit = 1
Type-3: B bit = 0
Type-4: B bit = 1
- [E&M-P Pulse Length] Seizure
1.150 ms (Default)
2.600 ms
Specifies the pulse length of the Seizure signal.
- [E&M-P Pulse Length] Answer
1.150 ms
2.600 ms (Default)
Specifies the pulse length of the Answer signal.
- [E&M-P Pulse Length] Clear
1.150 ms
2.600 ms (Default)
Specifies the pulse length of the Clear signal.
- [Meter Pulse Detection] Mode
1.No Detection (Default)
2.Outgoing call only
3.Both calls
Specifies whether detecting the Metre Pulse signal transmitted from the Central Office or not.
Metre Pulse Detection can be set to "Outgoing call only" or "Both incoming and outgoing calls."
- [Meter Pulse Detection] Bit Position
1.A-bit
2.B-bit (Default)
3.C-bit
4.D-bit
Specifies the bit position for the Metre Pulse Detection.
- [Meter Pulse Detection] Length
8 - 480 ms in 8 ms increments (Default: 128 ms)
Specifies the time range the system requires to detect the Metre Pulse signal transmitted from the Central Office.
- DSP Gain Adjustment
Used to adjust the signal power of the DSP (Digital Signal Processor).
- [DSP Gain Adjustment] DTMF Transmit
-12 to + 3 dB (Default: -3 dB)
Specifies the output power of the DTMF signals transmitted from the DSP.
- [DSP Gain Adjustment] DTMF Receive
(-42 - 0) to (-11 -0) dB (Default: -26 - 0 dB)
Specifies the strength range the DSP requires to detect the DTMF signals.
- [DSP Gain Adjustment] MFC-R2 Transmit
-31 to 0 dB (Default: -16 dB)
Specifies the output power of the MFC-R2 signals transmitted from the DSP.
- [DSP Gain Adjustment] MFC-R2 Receive
(-38 - 0) to (-23 -0) dB (Default: -30 - 0 dB)
Specifies the strength range the DSP requires to detect the MFC-R2 signals.
- [Frame Error Detection] Error Detection
1.Yes
2.No (Default)
Specifies whether the system detects the frame synchronisation error or not.
- [Frame Error Detection] Error Rate
No limit, 16 - 112 errors/s in 16 errors/s increments (Default: No limit)
Specifies the number of frame errors per second which the system requires to recognise the remote alarm.
Если можно подскажите по позициям какие параметры выставить в Панас-е, чтоб состыковать с Алкателем.